Products >> Industrial RO Element >> Hydranautics RO Membrane Element

Hydranautics SWC5-LD RO Membrane

Product No.：SWC5-LD
Online Inquiry

RO Membrane Element SWC5-LD

Hydranautics SWC5-LD membranes are available in a range of innovative formulations that are suitable for varying degrees of seawater salinity. They are an excellent choice for customers seeking to optimise salt rejection and permeate fluxes. Each offers the highest productivity and salt rejection rates in the industry, combined with optimised flow, low fouling and low energy consumption. These membranes are particularly useful when lower permeate TDS and lower feed pressures are needed. In addition, SWC5-LD membranes offer maximum energy efficiency at the lowest costs, making them a popular choice for use in large-scale desalination plants.
Hydranautics SWC5-LD Product Data Sheet

Specified Performance

Permeate Flow	9,000 gpd (34.1 m³/d)
Salt Rejection	99.8% (99.7% minimum)
Test Conditions	32000 ppm NaCl solution
	800 psig (5.5 MPa) Applied Pressure
	77 ℉ (25 ℃) Operating Temperature
	10% Permeate Recovery
	6.5 - 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified.

General Product Description

Configuration	Low Fouling Spiral Wound
Membrane Polymer	Composite Polyamide
Membrane Active Area	400 ft² (37.2 m²)
Feed Spacer	34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box.

Element Details

A, inches (mm)	B, inches (mm)	C, inches (mm)
40.0 (1016)	7.89 (200)	1.125 (28.6)

*Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions^

Maximum Applied Pressure	1200 psig (8.27 MPa)
Maximum Chlorine Concentration	< 0.1 ppm
Maximum Operating Temperature	113 ℉ (45 ℃)
pH Range, Continuous (Cleaning)	2-11 (1-13)
Maximum Feedwater Turbidity	1.0 NTU
Maximum Feedwater SDI (15 mins)	5.0
Maximum Feed Flow	85 gpm (19.3 m³/h)
Minimum Brine Flow	12 gpm (2.7 m³/h)
Maximum Pressure Drop for Each Element	15 psi (0.10 MPa)

^ The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane. See Hydranautics Technical Bulletins for more details.

Disclaimer: The information and data are presented in good faith and in lieu of all warranties. All express or implied warranties, including the warranties of merchantability and fitness for a particular purpose, are hereby disclaimed and excluded. Conditions and methods of use of our products are beyond our control.
Hydranautics assumes no liability for results obtained or damages incurred through the application of the presented information and data. It is the user's responsibility to determine the appropriateness of Hydranautics' products for the user's specific end uses.

Notice:
If your customer insists existing brand, please contact Hydranautics or its distributors.
If you and your customer accept economical & quick-delivery equivalent of similar or better performance with same warranty, kindly send us an inquiry now.

Previous Product：Hydranautics SWC5-LD-4040 RO Membrane Next Product：Hydranautics SWC5 RO Membrane