Products >> Hollow Fiber UF Membrane >> DuPont DOW UF Membrane Module

DuPont IntegraTec XP 51 IP IG

Product No.：XP 51 IP IG
Online Inquiry

Features

The DuPont IntegraTec XP 51 IP IG with XP fiber are made from excellent permeability, high antifouling properties, XP™ Hydrophilic PVDF Fiber. The modules provide excellent performance, industry leading membrane area with low energy and chemical consumption. The XP 51 IP IG modules have the following general properties and characteristics:

Proven XP™ Hydrophilic PVDF Fiber:

– Superior fouling and chlorine resistance.
– High colloidal particulate, bacteria, and virus log removal rate.
– Excellent filtration permeability.
– Easy cleaning and wettability.

Optimized Module Design:

– Innovative end cap to direct coupling of modules in IP skids with simple assembly and scalability.
– Short module design to suit height restricted or containerized installation.

– High operation recovery with high air scouring tolerance.
– Reduced chemical consumption with maintenance cleanings protocol.
– Robust materials for long lifetime.
– Easy installation and low maintenance.

The DuPont IntegraTec XP 51 IP IG module is shorter in height, higher in recovery and is suitable for applications where height is a constraint.

The DuPont IntegraTec XP 51 IP IG can be used for a wide variety of treatment applications：

– Municipal drinking water.

– Industrial utility water.

– Industrial wastewater reuse.

– Municipal wastewater filtration.

– RO pretreatment.

DuPont IntegraTec UF Membrane XP 51 IP IG Product Data Sheet

Product Specifications

Part No / GMID

Mode of Filtration

Type

Material

Pore Size

Operating Process

Other Wetted
Module Components

XP 51 IP IG

12091626

Out-In Pressurized

Hollow fiber

PVDF (Polyvinylidene Fluoride)

0.03 μm

Dead-end

Polyurethane, uPVC, EPDM, and ABS

Figure 1

Figure 2

Properties

Membrane Area

Weight

(shipping/empty/filled)

Hold-Up Volume(Clean-In-Place = CIP)

(Feed/Membrane Structure/Filtrate)

Product

m2

ft2

kg

lbs

liters

gallons

XP 51 IP IG

51

549

69/53/102

152/117/225

32/9/9

8.5/2.4/2.4

Dimensions

Units

Length

Diameter

Width

L

L1

L2

L3

D

W1

W2

SI (mm)

1,988 ± 3.0

1,500 ± 3.0

1,689 ± 3.0

1,864 ± 3.0

225

360

342

US (inch)

78.3 ± 0.1

59.1 ± 0.1

66.5 ± 0.1

73.4 ± 0.1

8.9

14.2

13.5

Operating Parameters

Operating Temperature Range

1 - 40 °C

34 - 104 °F

Operating pH

2 - 11

Cleaning pH

2 - 12

Typical Filtration Trans-Membrane Pressure (TMP)

0.4 - 1.5 bar

5.8 - 21.8 psi

Typical Backwash TMP

0.6 - 2.0 bar

8.7 - 29.0 psi

Backwash Type

Air scour with liquid backwash

Backwash Flux

100 L/(m²h)

58.8 gfd

Backwash Flow

5.1 m3h

22.4 gpm

Rate of Pressure Change (Max)

0.5 bar/sec

7.3 psi/sec

Inlet Pressure (Max)

6.25 bar (at 20 °C)

90.7 psi

Filtration TMP (Max)

2.1 bar

30.5 psi

Backwash TMP (Max)

2.5 bar

36 psi

Filtration Flux (Max)

110 L/(m2h)

64.5 gfd

Filtration Flow (Max)

5.6 m3h

24.8 gpm

Backwash Flux (Max)

120 L/(m²h)

70.6 gfd

Particle Size (Max)

300 μm

Exposure NaOCl (Max)

≤ 1,500,000 ppm x h

Recommended max. instantaneous exposure NaOCl

2,000 ppm

Operation guidelines

Avoid any abrupt pressure variations during start-up, operation, shutdown, cleaning or other sequences to prevent possible membrane damage. The maximum pressure change allowable is 0.5 bar/s.
Please refer to the latest version of the DuPont™ IntegraTec™ PVDF-UF Out-In P Series IntegraPac™ Rack Assembly Manual.

General information

If operating limits and guidelines given in this document are not strictly followed, any warranty will be null and void.

To control biological growth during extended system shutdowns, storage solution has to be introduced into the membrane modules.

Regulatory note

Certified drinking water modules require specific conditioning procedures prior to producing potable water. For operating parameters, please refer to the DuPont™ IntegraTec™ P Series PVDF-UF OUT-In-Progress and Design Manual.

Drinking water modules may be subjected to additional regulatory restrictions in some countries. Please check local regulatory guidelines and application status before use.

Version: Form No . 45-D03863-en, Rev. 1

Notice:
If your customer insists existing brand, please contact DuPont or its distributors.
If you and your customer accept economical & quick-delivery equivalent of similar or better performance with same warranty, kindly send us an inquiry now.

Previous Product：DuPont IntegraTec XP 51 IP Next Product：DuPont DOW UF Membrane IPD-51XP